I picked up a used 80k (allegedly) 1g awd trans. After some reading last 4 digits NPZS is a 89-90 trans, I have the 22 spline t-case also.My laser is a 92, with a 23 spline t-case and a trans that grinds REALLY bad, but is a 6/5/4 laser.engine is fresh put together ready for 500+ but I’m...
About to get suspension for my 1g. Looking for thoughts and info on these two. I have koni GC on my 2g but hear nothing but good on Feal.Car will be mostly on the street and car meets. Will be doing some drag and few auto X more drag though. A good amount of Spirited driving in the...
double checking as I have read other people gapping to something little bigger.Got my engine back from the machine shop, setting my ring gap the instructions say1st ring = bore X .0050
3.386X .0050=.0169 or .017
2nd ring = bore X .0055
3.386 X .0055 = .0186 or .019I have read other...
so I just got my block back from the machine shop. Main caps where held down with the stock bolts when honed.Do I have to get this redone with arp’s holding it down? I just read about this now.Should I just use the stock bolts?
Looking to see what kind of 20g this is, if it is, and what kind of numbers if possible.It was a little laggy as I remember, full boost by 5k little after. Motor is out and at matching shop. Looking for 400-450whp maybe 500 but that’s very tops. It made 290whp low boost and low timing before...
I finally got AWD. NO RUSTLong story short, buddy of mine lost interest on his build and I now have his 92 laser RS. I have helped him with this car a lot.-Mods I know of
Engine .040 over forged internals (i forget what we put in)
Balance shaft delete.
New head, valves, seals, beehive...
So I just got a 1g laser awd 6 bolt. The water pump went bad on me when I was driving it home after I purchased. Sucks but o well.So I got everything done and I am setting tension on timing belt. When I set the tensioner pulley the 2 holes are around 12 o'clock and 2 o'clock, maybe a little...
So based on the FSM one wire from EGR solenoid comes from MFI relay and the other goes to ECM that is the green wire red stripe goes to pin 6. I am hoping someone can confirm the other pic i posted is the red wire going to EGR red wire. Thank you guys for always hhelpig me.
So I am about to purchase a welder for some exhaust needs and some body work needs. trying to see if this 120v mig will do or if I should double up and get the 120v/240v tig.the mig I'm looking at...
My question is how important it is to see .49 and 5.0? (I can't find this answer no matter what question I put into google)Or is it get as close as you can?First want to state I have no idle issues or no drivability issues, and I'm hoping this is an easy question. This is the first thing to...
So this weekend I put on my down pipe, 95 ECU with link V3, and my wideband LC1. Everything is in and wired, went to remove the o2 (rear) so I can put in the WB. Got out torch and impact gun as even with my 3 foot breaker bar it wouldn't budge. Heated it up and took the gun to it. Well it...
Any MOD can relocate if you want, wasn't sure where to post. But thought I would share, let me know what you think.Well I am getting ready to paing my car, just got a 60 gallon air compressor. When using air tools with it, I got a lot of water and moist air spraying from gun and DA sander. So...
So I am going through my inspection and emissions, I replaced my battery a while back and never drove the car. (Have a work truck) none of the sensors are ready with a pending EGR checked engine.While back I replaced my head, belt, and so forth. Every now and then my check engine light would...
Ok, so I went to DMV to register my bike, come out and my car dies.As I turn the key all power and lights turn off. Last time this happened a ground came off. My ground is their, my terminal was dirty. I'm in a parking lot with a o Riley's here ran over got a basic wrench kit sand paper Coke a...
So today I was able to get on charlotte NASCAR raceway.It was an experience, those banks where nice. Was able to get ER up to almost 110 around the turn. Was at the end of the line and able to make it up to number two out of 20 cars. I will be trying to load my video up from my phone. Did 12...
Was going to originally ask for thoughts but I figured it out and thought I should share. Hope it's in the right spot, feel free to move the post.So 2 weeks ago I was driving my car, like normal and all of a sudden when I would shift into any gear I got a lot of resistance (with car running or...
So wasn't sure where to put this.My neighbor is looking at buying a 07 eclipse for 6900 112k miles.I don't know anything about these cars, he is taking me as he likes my GST. But what should I look for, I'm good with basics like fluids, pads, new plug wires, belts, tires, dings, or...
So I am about to go look and possibly get was is said to be a big 16g. He want 60 bucks so I was like hell yea. But looking at the serial number, it seems to be a 14b. Just want to be 100% before I drive 60 min to find out it is in fact a 14b. Thanks a lot.
Wanted to post this as my car wouldn't start with a no crank issue, hope it helps someone else.These are the threads I referred to for help1.http://www.dsmtuners.com/threads/stumped-on-no-start-no-crank.416211/2.http://www.dsmtuners.com/threads/no-start-no-crank-more-info-inside.426334/...
So I was taking my tdo5h big 16g apart getting ready for rebuild and found this.Not sure if the picture went through, haven't added any sense the site changed over. But their is a small chip taken out of one fin on the ex turbine. Is this a big deal or not to worry?
So I got new seats for my car, I used the rear seats for my fire pit seat using the seat belt spot as cup holder.Has anyone made a gaming chair from their seats. I will be when I move to NC, but wanted people to post a pic of theirs if their is anyone.
So I got a job offer from the company I just left back on November. Hoping it goes better down their. Wouldn't have to be dealing with the same manager. I'm nervous about it, have been living with mom for 24 years now. But I think it is time to go.How is the DSM scene down their? I won't have...
:beatentodeath:So I am going tomorrow to pick up a bunch of wanted parts. Sorry if it's called something else, but i don't no LOL, brake distributer (the thing on the fire wall), will the GSX distributer be ok with 3000gt calipers and mounts. I just don't no if I need it off the 3KGT or will...
:idontknow: So my sun roof is off track or something. When I go to open it, it will only tilt open will not slide back. Then when I go to close it the passenger side will close snug, but driver side is slightly open. Too the point I can see through it. Not too sure of how to start.how do I...
So I have been reading a lot on this but haven't found actual fixes, or what to look at/how.When I let off the gas and slow down I hear a grinding sound. 4th and 5th is the most prominent but can be heard in 3rd and very slightly in 2nd. Higher the RPM the louder the sound also.Possible...
So I just threw my idiot light and it came back as a p1104 :thumb:
I have it plugged in and all just not hooked up to anything like vac lines. Has been like this for 2 years or so. That orange light is bugging me really bad and before I try to buy a new one I want to make sure it's bad...
So I just swapped my head recently, ever since I have been running hot.Problems I have found thus far,
1 didn't bleed properly first time,
2 fan wouldn't come on
3 coolant cap not holding pressure,Now I have fixed all three of these problems but I seem to be still running hot. My...
So I finally got my rebuilt head on, went to mock up my front mount and came across this. A rubber hose bends to a kink, and I can't seem to find a S bend hose. I was going to cut it and reverse that pipe on the intake and re weld it But my dremel won't cut through it :ohdamn: so my next thought...
So I just changed my timing belt maybe 3-7k miles ago. I will be changing my head hear soon, do I need to get a new belt and tenser again?:hmm:I think I will be fine I just want some other input befor I decide to save a little money and then find out I shuld have done it. :thumb:
Yesterday I started my car, it started just fine and sounded just fine. No lifter tick now that it's warm outside, but I still let it warm up. Once warm I heard a slight grind more like a rattle, I poked around with a long screw driver to see where the noise was comming from and it sounds like...
Ok so I have been trying to logg with evo scan for almost a week now, and with some patience I have finaly got evoscan/flash installed and ready to start logging. I got the Vag Com 409.1 cable to logg with for now, but I cant get it to work. I get an error from scan saying cable not responding...
So I moved into my appt complex about a year ago, and I have had my dsm now for 2 and half years. When I moved in here their was 0 dsm's. Now I see about 8 or 9 of them all being 420a's. I got alot of complement on my car when I come in and people hear my BOV. never thought they would multiply...
Ok so I got my 16g installed on my car running a 14b wategate at about 10psi creeping to 13 at 6.5k, I am staying out of boost untill I start doing some loggs. I am looking at a computer on craigs list for 90 bucks. I am only going to use the comp. for my car so this will be sufficient? Not...
I am about to make a 2 hr. trip to go get a 16g. Now I was told it is a mhi evo
16g but the picks I got did not say td05h on the housing. He said its a new compressor housing, is their another way to tell if its a mhi 16g? :hmm:please I dont ### to buy a piece of crap. :pray:sorry for the...
Just like the title I am rebuilding a spare head that I have. It is getting a valve job and some slight porting. I am only going for about 250-300, I have a 14b, 650cc, a 190lb pump, front mount will be comming later, and I will be tunning with evoscan / ecu flash.I am looking at getting...
Ok so I am rebuilding a spare head I have, and getting some hks 264 cams for it. My question is do I need to tune for these right away? I do plan on getting it tuned but that is after my 14b, front mount, injectors and pump ect. I need to do a timing belt soone and just figured the head shuld be...
I realy didnt want to make a post about this but I want to find the turn signal fuse. :ohdamn: I dont have the caps to the 2 fuse boxes so I dont know what is what. I have searched but all that comes up is about the relay.My turn signal wont turn off and my part is on order. I want to...
:cry:I hope the pic went through.But I went to the 1/8 mile and heard some light knocking comming from the head. Took off cover and saw this, looks like I got a little too hot. :cry:But anyway does this mean I have to tare it off and put on a new one? (more or less). I have a spare...
ok so I removed the bcs restrictor on my gst a few weeks ago, and began hitting about 20 pst then drops at higher rpm's. I know this happens to a good amount of people, how did you guys fix it?I got a MBC over the weekend and I no its hooked up right. I have no leaks besides a tiny one in...
So was woundering if the imformeter was a good logger to start with. I will be getting into tunning soone and just want to start logging to learn what I would be tunning.So any tips would be greatfull :thumb:
so my friend is going to buy this car on wed. Just wanted to see what you guys think of it?1992 Plymouth Laser DSMMy friend talked to him, he said that it had a 6 bolt in it. It sais on his post he has
2g pistons. I didnt think you could do that? most of the parts are not on the car...
I will start off by saing that I got a long block a little while back and was planing on building it. But what I plan on now is to just rebuild the head and swap them out to get rid of lifter tick, or valve sticking, (not shure witch one it is but I want it to stop) and just have better air...
I am putting my koni gc set up in my car and their are two diffrent size springs a thicker spring and a thinner spring. the thicker one has a bigger diamiter also. My question is whitch one is the front spring and whitch is the back. I think the bigger one is the front and the thinner one is the...
Ok so I am just excited I finaly ordered my ground controls for my Koni's. I got the koni's last check and I and I got enough to get my GC's so yea.Dont know if yall are interested but the previous owner didnt reat this car too well. He lowered the car 2in on GR2's stock replacements. So...
So I am buying lower control arms and lateral arms for both sides. What is everyones opinion on buying from a parts car. I dont mind buying new lateral arms those arnt that much. But the curved arm is like 150 at the low end (or at least that is all I have found). Is the dealership recal for the...
So i was going to ask if awd and fwd koni yellows are the same, but I found it. Now I have to ask why is their no diffrence. Almost all others their is a diffrence. I am ordering them this weekend but I just got to know befor I get them.
:thumb:If I missed this answer somewhere let me know please
So I got the hanes repair manual, and when I was picking it I chose the 2G eclipse book. when I got the book in the mail it said it was for a 95 through 05. Just woundering if this is what they all say or did I get the wrong one. I have looked through it but i notice that alot of the picks are...
Does anyone have any imput on megan racing EZ street series coilovers? I was originaly going to go with the tokico illumina's but I saw theese.
Megan Racing EZ Street Series Coilovers - 2G DSM 95-99 Eclipse - 2G DSM Coilovers - 2G 95-99 - Suspension - DSM Performance Parts | DSMparts.com
I...
I was changing my door hinges today because my door drops like and 1/8th of an inch, so the latch won't line up right. In the process I found out that it wasnt the hinge that was bad. I have a crack where the bottom bolt of the bottom hinge bolts to the body. Is their a way to fix it, it looks...