To use 4g63 belts on a 4g64 block swap with a 4g63 head.Get part: T41239 manufactured by GatesThis is a Subaru Idler pulley which is half the size of the Mitsubishi pulley. NOTE: THE BOLT HOLE will need to be bored out slightly to fit the Mitsubishi bolt in. This is the EJ engine Pulley that...

I have decided to go with a 2.3L setup on my 7 bolt short block. I am going to sleeve the cylinders, and from a rough estimate with all of the upgraded parts and turbo and intercooler, I should be landing roughly around 650hp-750hp at the crank without the nitrous, 750hp up to 1000hp With the...

I had to stay quiet about these but I've had them for a little while, doing a forged 94mm crank, 156mm Vader aluminum rod build. Should help get those revs up fast and handle everything I can throw at them.

Hi there, I got a SOCH 16 valve 2g carbureted 4g63 (galant 1993). I'm in tight budget and I have not access a lot of parts. I'm trying to build NA Stroker DOCH 4g63, I got DOCH head and It's ok. My problem Is about stroking, I can buy 4g69 crankshaft (there is NO other option for me) and with...

I know this question has been posted countless times on here, but I haven't been able to find anything more recent than 2015! I just bought a Manley Billet 100mm Crank (The stronger one of the two they make) and I have Manley Turbo Tuff I-Beam rods. It looks like I will be pushing around 650hp -...

I have a 2.4l fwd automatic trans convertible 3g eclipse w/ the 4g64 sohc. So I want to install a 4g63 head dohc stroker but don’t have any experience wrenching so for starters I want to know if I need to buy the heads off an auto fwd or can it be from a mt? And as I believe mine is a 7 bolt I...

I have up for sale an early 6 bolt g64b 100mm crankshaft same as 4g64 and g4cs came off an "90 mitsubishi rwd van with 162k miles on the odometer it was an automatic equipped van so minimal side load on the thrust bearings, it is uncut never polished or hot tanked, i'm asking $300 including...

Firstly, I would like to apologize for any terms used incorrectly. I'm Brazilian and I have a little trouble translating some parts of the car.I'm redoing the engine of my car. Currently it is a Stroker 2.3, with crankshaft 4g64 in measures standart and pistons Wiseco 86mm 9.5: 1. If my...

Finally selling my old girl. All the details are in my profile. Entertaining any reasonable offers. It currently sits on 235/45r17 Toyo proxy r888r tires with some life left in them (used for 2 Autocross seasons). Very well balanced for Autocross. Back half of interior is gutted so not much of a...

Im new here. I have a 95 eagle talon tsi with a brand new head and a blown up transmission, and a 2003 eclipse with the 2.4. Im trying to figure out a build sheet for my talon and i dont know if its better to just build the 4g63t or make it a stroker. Any input is welcome

james green submitted a new DSM Profile :Jgreens 1st dsmRead more about this vehicle here...

Hello everybody! Thais os my first thread here and first of all: sorry if i am posting it in the wrong place... I can move the post if someone warn me. I'm from brazil and this is the specs of my 2g:4g63t stroker (2.3, wiseco forged pistons and original rods) Turbo: forced performance 68hta...

I recently bought a gently used in excellent condition OEM Mitsu 4G69 7-bolt 100mm stroke crankshaft on eBay for a 7-bolt long rod 2.4L build. Due to my 4G64 block having a crack I have no choice but to let this go. This crankshaft is in absolutely pristine condition and is ready to drop right...