I have attempted to find this info without really getting a confident answer. However, I can only assume it is due to a supersession, but my part catalog does not show this.In the photos you will see two 5th gear assemblies next to each other. The one of the left came out of a 1993 GSX AWD...
In the photo you will see the intermediate shaft assembly sits slightly higher than the input shaft assembly in the case. I believe this is causing too much clearance between the input shaft bearing race and the case which doesn't crush the solder at all when assembled.
I did replace both top...
I could give the story but I dont want to waste too much or your time. So are the shifter bushings that attach to the transmission on a NVT350 (420a) trans the same ones as the 4g63 transmission? Or where could I order a new set of bushings or a replacement for the old ones?
So my car blew a clutch (ACT2600) a while back. (pressure plate fingers blew off, and disc was worn)I Removed the transmission and installed a new ACT 2600 sprung hub 6 puck assembly. I also installed a new Slave cylinder, Clutch fork, and throw out bearing w/clip. I then bled my clutch many...
Hello everyone, my girl is 1998 GS and i need to change transmission from auto to manual and i want to know, what is the difference beetwen F5mc1 and A578 transmiossoins:
In Chrysler PT cruiser is running A578, can i put this box to in eclipse without changes?
Thanks!
I replaced my master and slave cylinder about two weeks ago. I had the same issue at first after installation. The car would shift when the vehicle was off and I could start it and drive in a gear but when the car was running I couldn’t shift out of the gear I was in nor could I shift into any...
Hey guys so I just got my transmission today. I just would like to make sure that it'll bolt up to my 97 4g63 and everything should work. The clutch slave looks different from the one I ordered. If you can inform me on anything I should know im all ears.
As everyone here knows I recently rebuilt the manual trans on my '92 Talon TSi AWD. It was actually a '94 AWD trans as the dealer swapped it out back then due to some issues I vaguely recall with shifting into 2nd or 3rd. I rebuilt it because it kept popping out of 1st and was sometimes grinding...
So I got my stacks reassembled with new parts and did the solder method yesterday, but many of the measured values seemed way off. Then I realized that I might have done it wrong.What I did was first install all new or removed bottom (closest to clutch/engine/bellhousing) races into the case...
HI,
I am trying to isolate this weird oscillating metallic chattering noise coming from the bell housing area @ 2800-3000 RPM.When driving and accelerating the noise comes in steady at 2800-3500 RPM and then goes away,. Noise is pretty much only occurring in that RPM range.I have noticed...
As many here know I've been restoring my sub-78k miles manual trans '92 Talon TSi AWD for some time now, and it's finally time to fix the trans, the main issue being its popping out of 1st gear most of the time. I replaced the clutch last year, with a SBC Stage 2 DD kit, with the intention of...
Hey all,I have been searching and searching on where to find an ether a new transmission or a possible fix to the one I have. The transmission was broken recently on my 95 eagle talon and a chunk of it flew into the my clutch. I don't have the chunk that broke but it now has a 3-4" hole in...
I'm about to drop the trans on my '92 Talon TSi AWD to replace the clutch and fix a shifting issue. The car is parked in a driveway with the passenger side pretty close to a wall, around 18-24", enough room for me to remove the wheel and work on the knuckle and everything else there, but still a...
I'm currently in the process of repairing and restoring my '92 Talon TSi AWD manual, aspects of which I've discussed in other threads. One major task is replacing the clutch, which faded to nothing around five years ago and ultimately forced me to store it in a neighbor's driveway since I had...
Hi Fellow DSM owners. Reaching out for some help as I've spent hours searching the forums and Google but have not found anyone with the same issue.
I had my 1991 Eclipse GSX in storage for over 10 years. Prior to placing the car in storage there were no engine nor electrical problems. Car is...
I'm building a 99 eclipse with a 97 4g63 drivetrain (FWD) I am pretty much done with everything and its good to be driven on the road once I get this one issues settled. When in 1st gear if you start to let the clutch out the transmission will pop out of gear and sometimes grind. It used to be...
I found this while scrolling through Miller Imports. I know some of you have been searching so here you go:https://www.millerimportparts.com/95-99-Eclipse-Talon-Avenger-Sebring-420a-Manual-Transmission-2g-96-97-98-99-P3244131.aspx
owned since 2006, this is a project car. 169,000 miles manual transmission is good, Engine runs with no CELs but needs to be rebuilt or replaced. Has custom white and tan leather interior (2014), 2 Pioneer 6x9 3 way speakers(2014), cx300.4 series multi-channel Kicker amp(2014), 5.1 inch...
I am currently missing part number - MD744671I need it to finish my conversion for my eclipse....Its an "adapter" for the tranny my mits dealer told meBelow are some pics
For sale, the transmission right out of my car. Currently running and driving perfectly. Has like 100 miles since a top to bottom refresh from TMZ performance and myself. Evo 3 1st through 4th gear, double syncros, welded center diff. Also will include good condition front axles and...