Hello everyone,I am currently rebuilding my transmission because my 3rd gear went and it looks like it overheated. I was doing research online and saw that kiggly racing recommends porting the valve body oil passage. Does anyone know if this is truly necessary...
I am having a problem with my transmission. When I put the car in reverse I can feel it engage and the car barely moves. When I give it gas it feels like the car is just free revving. I checked the valve body to make sure the O-ring for the low reverse brake was there and replaced it. I also...
I am trying to adjust me kickdown servo and I am using the translab instructions to adjust it. The instructions say to put in a 1/16 drill bit into the servo pin cushion and then air measure it through the band apply hole. Can someone that has done this help me out. I am trying to measure the...
I just recently rebuild my transmission. The problem I am having is the car won’t shift into 2nd and 4th. As of right now 1st, 3rd, and reverse or working. When I shift the car in 2nd and 4th it feels like the car is not changing gears. When I shift into 2nd it feels like it’s still in 1st and...
1). Any boost, vac, or exhaust leaks? Boost leak tested 5psi above your max boost with no leaks?
No2). Verified mechanical timing?
Yes3). Verified base timing?
Yes4). Ignition system
COP or Stock Coil: Stock
Wire brand and Age: NGK, 3 Months Old
Spark plug brand, type and Gap: NGK BPR7ES...
I have an axle shaft that has 22 spline were the cv joint connects to the shaft does anyone know what type of shaft it could be. I need the cv joint and I was told it was from a 2G but it doesn't fit because the one I bought has 25 spline.
I just converted my GST to AWD and I was looking for real axles but I can't find any stock axles anywhere. Does anyone know where to find stock axles? Also are there any other options for the rear axles other than driveshaft shop?
I am converting my car from FWD to AWD but the problem I am having is when I put the car in reverse for some reason the tires spin forward. I am using the kiggly mod also, I have checked to make sure the solenoids are good, and I also checked to make sure my transmission pump works. I have no...
I recently replaced my transmission pump on my W4A33. I wanted to know if there is a specific way of putting the input shaft plus everything on the input shaft. I did not disassemble anything on the shaft but when I put it back together and installed it in my car I had no reverse. Also I bought...
Hello all,I am converting my car from a gs-t to a gsx so I bought a complete swap. When I installed the transmission in my car I kept hearing grinding noises so I decided to remove the transmission and see what was going on. I removed the transmission pump and found that the gear was damaged...
1). Any boost, vac, or exhaust leaks? Boost leak tested 5psi above your max boost with no leaks?
No2). Verified mechanical timing?
Yes3). Verified base timing?
Yes4). Ignition system
COP or Stock Coil: Stock
Wire brand and Age: NGK, less than a week old
Spark plug brand, type and Gap: NGK...
Hello everyone,I am having an issue with my car breaking up at high rpms. It usually starts to break up at around 5k and doesn't stop. The rpms will still go up but it will break up all the way through. I have uploaded a log and a video so you can see. If there is anything else you guys can...
Hello all,I have a 1997 GS-T the car is running to rich and when I start it revs up real high then settles for a moment and then it just dies out. I have tested the following parts by switching them MAF, TPS, and EGR. I cant get the car to idle at all. I do noticed theres alot of noise...
Hello all, I have a 2g with a 1g throttle body. I am trying to eliminate my idle air control valve. I made a block off plate to eliminate the idle air control valve on the throttle body but when I re installed the throttle body and tried to start the car it did not want to start. Has anyone...
Hello everyone I wanted to ask you guys for some advice on what type of injectors I should buy. I am going with 1200cc injectors just need to decide which brand to get. I have seen FIC, TRE, RC, and PTE I wanted to know if any of you guys have had any personal experiences with any of these? The...
Hello everyone, I am having a problem were I am not getting any spark on cylinder 1 and 4 but I am getting spark on cylinder 2 and 3. I have check the coils by switching the wires and switching the coils and both coils are good. I also changed the power transistor, the cam angle sensor, the ECU...
Hello everyone,I am having a problem where none of my accessories in my 2g eclipse work. My power windows, power locks, and radio are not working. I do not know what it can be I have checked all my fuses inside the car and in the engine bay. All the fuses are fine and none of them are blown...
Hello everyone,I have a 98 Gs-t that I have had in my garage for a couple of years now as a project car. I am currently trying to finish it since I do not have alot left. I recently have been running in to some electrical problems. One of my problems is that I am not getting 12v constant...
Hello everyone,I am undecided on whether to stay with my convertible gs-t or get a hard top that I found for a good price. I am trying to build a fast street car and eventually a track car. Which would be better for a track car? I have my motor built and if I decided to buy the hard top I...
Hello everyone,I am currently having a big problem with my 98 gs-t. I do not know why but one of my coil packs are heating up to the point that the coil pack is melting. After all the research I have done the only thing I have been able to find is that it could be my power transistor or my...
i finally finished building my 2g fully built i am missing an intake manifold i was checking out on eBay because i did not know were to start i want the best manifold out there for the price but i see a lot on eBay that say 50hp to the wheels which is the weapon r but that can possibly be true...
i have just recently put an lsd in my tranny but i dont know remember were the plastic oil guide goes thats all im missing to finish the tranny and put my motor in the car if anyone knows exactly how it goes on the 2g with pictures so i can see it exactly i would really appreciate it
anyone know were i can find some axles for a 2g gst that holds around 600hp i am currently looking for some axles that wont snap but have only found ones that hold 300hp if anyone knows i will really appreciate it
anyone know were i can buy performance gears or parts for a 2g gst spyder any recommendations i want to do a complete build on my transmission any suggestions ???
im trying to take apart my manual tranny on my 2g but for some reason i cant take off the trans axle casing and i have taken off every single screw but i cant get the casing to come off like if it was stuck anyone got any ideas?
im building a 4g63 motor and i sent the head to be build with all ferrea parts but the guy at the machine shop told me if i go with stage 3 i need sold lifters and i will also need to port the head is this true or does he just want to take my money is the porting and lifters really neccesary
im building a 4g63 motor and i have the bottom end completly done and the head is being built with all ferrea parts i am going with hks stage 3 cams and the guy at the machine shop told me that i need solid lifters does anyone know if this is true and if so what are the best solid lifters out...
im building my 2g motor and after i got all the parts i saw that my stock crankshaft pulley had chips on the outer part of the ring and when i went to balance the motor the guy told me that the pulley was no good to buy a new one so instead of buying another stock i bought a light weight...
im looking to buy a clutch kit i was thinking anout act but i hear alot of bad things so i need to know what clutch kit to buy i would like it to hold atleast 500hp i know i might not ever get there but im just basically saying i want a strong clutch with PP
well i finally took my motor ro the machine shop and the guy told me he had to redo the whole head no problem, then he told me my block was good and was drilling my cylinder 2 go .20 over and then he told me that my crankshaft is bad and he would have to machine were the bearings were because it...