I just picked up a 3000gt front sway bar. It is "13/16 diameter bar. If it does we will have a choice of 3/4 13/16 1" and 1 1/8" bars. I will keep you posted if they are a fit.
https://www.galantvr4.org/ubbthreads/showflat.php?Board=UBB2&Number=908575&Forum=&Words=&Searchpage=142&Limit=25&Main=908179&Search=true&where=&Name=449&daterange=&newerval=&newertype=&olderval=&oldertype=&bodyprev=#Post908575
Check this out from 2010 . Called Curtis frame ties. What are your...
http://www.superpro.com.au/find/superpro-suspension-parts-and-poly-bushings-for-mitsubishi-lancer-evo-1-2-3-1992-1996-/cid-999500375
I have been in communication with Super Pro in Australia with the possible of these bushings fitting the 1st gen rack . I will keep you posted.
Rick
I was wondering if 3000gt sway bars are interchangeable with the 1st gen. Since the suspension is the same, could they be used in a 1st gen. It would open up more choices for our cars. It would be ok if it needed a few modds for the install.
Rick
I am having a problem with my car cutting out under partial throttle on hills. If I am climbing a hill at 10 psi at 3000 rpm the car starts to buck and stutter. I am not getting knock counts when this happens. Any idea what is wrong? Spark gap is right. Has new spark plugs, wires and fuel...
I have been searching the different Mitsubushi web sights. I came across installing 3000gt Bilstein HD inserts in a Galant strut housing. They also used a rear shock from a mid 80's BMW 325 . I found this at
Mitsubishi Galant VR-4 Forum - E39A 4G63
Belize 1334 used this set up.
I would think...
I was on the Mitsubishi Galant VR-4 Forum - E39A 4G63 web sight . Curtis one their more knowledgable people there. He made the clam that a 95 Mustang rear sway bar will fit a 1st g with some minor adjustments. Has anybody looked into this? The 95 rear bar is 27mm or 1 1/16 diameter. This could...
My next modd is fabbing a set of 96 rear brakes off a 96 vette.They have the same overall height of 49,9 mm. The diameter is 304.8 mm and vented.They are 80 mm thick.The caliper is a PBR that has a built in emergency brake.
The rotor must be machined for the center hole to 89mm and redrilledl...
I just finished mounting cobra calipers with crown vic rotors on the front.I would like to fabb some 11" rotors on the rear with stock calipers.Does anyone know an auto manufacture rotor that will interchange with a 1st gen. I can make hub rings and redrill the wheel studs.I am also plan on...
I just set my cars alignments specs. I am trying to get rid of the understeer to a more neutral steer.my new specs are
front
-1.7 camber
+ 4.7 caster
0 toe
rear
0 camber
0 toe
I am wondering what other's are setting there alignments at?I have not drove it much,but I think it is working...
I have been wanting to improve the shifter.I have the solid bushings at the trans.I have solid bushings at the shifter plate and heim joints at the shifter cable.Today I went down to the hardware store and picked up 2 bronze bushing
1/2" id by 5/8" od by15/16" long
I chuck them on the lath and...
I was checking out an evo forum and they have a kit from Whiteside.The bushings help correct the bump steer for the rear suspension. Has anybody checked the rear suspension on a 1st gen or a 2nd gen for bump steer? How did you lessen the bump steer?
I live at 7500 feet. I don't think my B.O.V is opening up fully.I have a factory 92 B.O.V.I checked my valve,it started opening at 53.3 kPa or 17" of vacuum .fully opened at 20" of vacuum. I don't get 20' of vacuum.Do they make an adjustable B.O.V or one for high altitude?
Has anybody built my heim joint shifter cable end at the shifter?It was posted in the tech section. I felt it helped the feel of the shifting.I also have the solid ends at the trans and the symborski kit. I would like to know if anybody has had the success that I have had?
I did something a little different with the rear sway bar links. I have heim joints at both ends with a male an a female theads. It worked out very well. I attached a heim joint to the sway bar. Then at the lower control arm. The sway bar end was bolted to it. The lower control arm,I bolted 2...
After market companies have developed different chassis bracing for the evo. Companies like NAGISA,G.T Spec, and Cusco. They are making braces for the the trunk,fender braces and lower center power braces.Does anybody have any experiences with these braces? Would these braces help our D.S.Ms. If...
The factory shift cable ends are sloppy plastic pieces. I replaced them with studded heim joints and have much better feel in my shifter now.Tools needed:
6x1mm left handed tap & drill bit to match
5/16x24 right fine tap & drill bit to matchParts needed:
two 5/16 heims with studs
two...
NOTE TO MODERATORS: I cannot upload any more attachments for pictures. I only have one picture uploaded to the site but I do not have space for more. I have two photos to go with this write-up I would like to add but can't.This is how I made a rear upper adjustable control arm.Tools...
has any body made rear sub frame bushing besides sheare motor sports? i was thinking of making some out of steel. then welding them in the sub frame. does any body have any other ideas? thanks
what is a polk performance tubular control arm? i checked there web sight and they had no pictures or any write ups. does any body know any thing about them?