Hey guys. Hope that everyone had a great Thanksgiving! I have some questions. Is anyone using their phones to log? Specially android and for the 1g.. I have done quite a bit of searching but haven't found a solid answer. Someone was developing a from of android logger. Mmcddroind or something...

Hey guys what's up? I tried looking but couldn't find anyone that STILL offers this service. I'm interested in having a chip burned for my 1g. Does anyone still burns chips and is willing to provide this service?Thanks guys.

Hey guys what's up? I have some questions. Is anyone successfully running without the ISC? I deleted the ISC after swapping to a Ford throttle body. I was running a remote mounted ISC but it went bad on me. So I decided to eliminate it and see if I could run without it. I really would like...

Hey guys what's up? I was wondering. Can ecmlink be installed and run with the stock tune or without the need to do any tuning? Why? For different reasons such as: needing to break in a new engine, having an old engine and just want drive it with the stock tune, not having the time and or...

Hi guys. I have a question. I'm relocating my battery to the trunk on my 1g. My question is: For those that have 1g DSMs. Where or how did you route your cables through the firewall? I read that some have route the battery cable through the hole that's close to the clutch and brake pedal on...

Hi guys. I'm having a little problem here in regards to finding some power source wires. I'm looking for a Constant 12v power source and an ignition only 12v source for some electronic gauges. I found three 12v wires with my multimeter. They are 1 red wire that connects to the radio, 1 yellow...

Hey guys what's up? I have a question in regards to wiring the Lc1 wideband on a 1g. I have searched but can't find an answer to this. I'm about to install my old yet brand new Lc1 wideband. I'm just bringing my car back to life after 10 years. I don't have ecmlink just yet. When wiring...

Hey guys what's up. So, my question. Is there any brake boosters that are smaller or acutally thinner than the stock one to fit into the 1g dsm that will mate to the stock master cylinder or even a smaller master cylinder for the 1g? I think that the colt or mirage might have a smaller...

Hey guys what's new? I have a quick question here that as simple as it sounds, I haven't been able to find the answer. What is the inlet diameter of the intake ports on the 6 bolt cylinder head? I believe the exhaust poertse are something like 1.5 to 1.75 inch in inlet diameter, not too...

Well, don't know where to post this. So i apologize in advance. My question here is: does anyone know if Magnus will have a v3 1g cast intake manifold group buy or a sale of sort? I tried contacting them but i have not gotten an answer. I guess it would depend on how many people...

Hi there guys. I have a question. Whats the diameter of the exhaust ports on a 6 bolt head? I would like to fabricate an exhaust header and would like to know the diameter for the exhaust runners. How big of a diameter to go. thanks.

Hi. Does anyone know where I could find a male connector for the female TPS harness connector wiring?I need it in order to make an adapter for a Ford TPS with GM connector to the 1g TPS harness female connector wiring. I don't want to cut off the wiring harness in case this thing doesn't...

Hi. I have some questions that I could not find.I'm doing a 2g head on my 1g. Also swapping to a 2g intake manifold to match the head ports. I of course have the 1g coil pack and power transistor. These 2 mount to the 1g intake manifold and they have a specific bolt pattern/placement that...

Those that have done the free fiav delete mod. How many times did you have to turn the black knob with the 4 dimples and cross like shape? I was only able to turn it almost 1 full turn. What do you guys think?

Hey guys. What's the biggest and best cooling radiator available for our cars that you know of?? I run the koyo radiator and its ok. It is more delicate than the stock radiator. Fins bend easier. It's a tad bit smaller than the stock radiator from side to side core wise. The stock radiator is...

Does anybody know if any Fabricators sell or make any isc adaptors for any aftermarket throttle bodies or for the stock throttle body? I want to eliminate the fiav but keep the isc. However, I don't want to use that big chunk of useless metal of lower throttle body. I know that fftec made an...

Ok guys, I have a question(s). When installing your ARP studs, you use the supplied lube which is ARP moly based specially formulated assembly lubricant. With this lube, your final torque on regular ARP head suds is around 80 LBS. Some will argue that its 90 LBS. Anyways, I'm in the market...

Hey guys what's up? Does anybody here know of a good machine shop in Omaha Ne?? I need to have some work done on my cylinder head. Valve guides and components. As well as re-surface the head. I know that there is a few but I would like one that you guys trust and that they had done some work on...

As title reads. Is there any custom fabricators here in Omaha Ne?? I need to have 2 exhaust silencers fabricated for my car. Tried looking for some universal ones from hks, apexi, greddy, DC sports, tanabe and the rest of the pack but nobody sells 73mm od silencers. Heck, not even 3.00 inch...

I'm surprise nobody has posted this or asked about it. Well, on to the questions: How are you guys running your lc-1 wiring from the engine bay to the cabin on a 1g or 2g? Preferably 1g. What about the lc-1 controller? Engine bay or cabin? If you have it in the engine bay, where are you...

The composite head gaskets have proven themselves well worthy. Not only are they more forgiving than an mls or copper gaskets when it comes to sealing a not so perfect head surface to block but they can withstand some serious boost and can be use as a fail safe/fuse of sort, often being a better...

I'm using permatex high temp thread sealant on some fittings for a new oil drain set up and oil pressure sensors and such. The direction on the cover say that it takes 4 hours to settle and 24 hours to fully cure. Well, my problem is that its been a week since I applied some of this sealant and...

I'm using permatex high temp thread sealant on some fittings for a new oil drain set up and oil pressure sensors and such. The direction on the cover say that it takes 4 hours to settle and 24 hours to fully cure. Well, my problem is that its been a week since I applied some of this sealant and...

I don't know where exactly to post this so I'll ask here. So does anybody know what happened to the fftec 75mm tb? Are they disontinued? Does anybody here run this tb? I called them back in march/april to ask some questions about the tb and possibly purchase one. Well after finally getting...

Hey guys what's up? Yeah I'm curious about it. I already done some slight research on it and I do know that the runners on the 1g have a bigger diameter than the Evo 3 and the 2g manifolds. This is to match the head ports and such.Installing a 1g mani on a 2g head won't work because this will...

Whats up guys. Just how the title states. How do you check, install an oil pressure tester on your oil feed line for the turbo. I have a holset that I will be feeding oil from the OFH. I have 4an stainless line with all the connections and a restrictor. It is very important to check the oil...

I'm in the process of installing my BEP bolton housing on my hx35. I ran into a problem. As I slid the housing on the CHRA, It doesn't seem to sit flush with it. Meaning that when I install the bolts and brakes, the same brakets don't fit correctly because again, for some reason I am unable to...

Hi I have some question about the egr and charcoal canister. It seens like there is some vacum lines that connect to the charcoal canister and the egr. I'm looking into deleting the egr and some of the vacum lines. This can help eliminate some of the common vacum leaks and clean up the enigne...

HI. Quick question here. How do you adjust the fpr (adjustable) when you have 272 cams? My problem here is that. Before my cams, I had my fpr adjusted to 37psi with the vacum hose disconected and plugged. My Idle was at 750rpms and I was getting vacum readings of about 18. It was all good. No...

Hey guys whats up!! Question here. Does someone know the inlet diameter of the spark plug holes?? I was doing some work on my car yesterday. I'm re-doing my valve seals and different cams and such. Well upon my valve spring compressor, one of the bolts that holds it in place slid off. I found...

As title says. It is suppossed to be 5 cranks per cylinder when doing a copression test. My question is: why only 5 cranks. Whats so special about 5 cranks instead of say, 6, 8 or 10? On the universal compression kit that I bought, it says to crank the car (motor) until the needle on the gauge...

HI guys. Whats the proper transfer case fluid to buy at the autoparts store other than online? I can't find Redline heavywheight shockproof, Redline MT90. I even went to the mitsubishi dealer and tried to get mitsubishi transfercase fluid for evos. They told me that they don't have any...

HI everyone. Just as the title states. For those of you that do your own timing belts. What type of beam type torque wrench do you guys use? The smallest ones that I have seen and that I own, only measure 2.5 lbs/ft. They go in increments of 2.5 lbs/ft. This is already a minimum of 30 lbs/in...

As title states. I have some questions on this. First. When splicing and connecting the wires on the new 255walbro fuel pump. Is it ok to use epoxy over the crimp/butt connector as an insulator so that there is no gasoline soaking it thus the potential of something igniting? I know its...

Hey whats up everyone! Well I have some questions on this. I couldn't find this on the Chiltons and Hayes manual. Maybe I missed it. 1st question: When repacing the timing belt tensioner. Do you use locktite on the blts that hold it? or instead do you use anti-seize? or use nothing and just...

Hey guys whats up! As the title says. I wouldn't post something as simple as this. I don't know if someone has run into this problem lately. I've been trying to find a set of these lower window trims for my 1g since january but had no luck. I tried all the vendors that I can think of that...

HI guys. As the title reads. To those that have the 1g pro-race intercooler. How much fo the bumper beam did you guys trim?? Because I pretty much work 7 days a week, I'm doing this intercooler install in stages. I went to the local junk yard and bought an extra pumper beam. This way I can take...

HI guys whats up. Well, I'm in the market for a fpr and components. I did my research and found various brands. As I'm trying to get the best for my car. Base on feedback from people and the research that I've done. I decided that the best one for my car would be Aeromotive brand. Well, upon...

HI guys, whats going on?? I have a couple of questions. What is the best or has the best cooling capacities of radiators available for the 1g. I know there is: visteon, koyo, fluidyne, mishimoto. I don't care for the price or pakages, kits etc. I'm not trying to save money, I just want the best...

Hey guys whats up?? Quick question. Who sells hypercoils for the 1g?? I know that Diamond Star Specialist used to sell the hypercoil suspension kit with konis and all but I think that DSS is no longer. I haven't been able to find them and nobody sells hypercoils that I know of. Does anybody here...

HI guys whats up?? Well, like the title says. I'd like to know the top best or thee best intercooler out there for a 1g dsm. Best overall fitment. The smallest most efficient for 500+hp. Not concern about price at all. Best design and flow, cooling capacity. Shortest piping route possible. I...

This is for a 1g awd. I would like to know which sway bars are stiffer RMs or suspension techniques. How thick are them? The thing is that I already ordered a set of ST bars but i culd still cancel them and go for RMs. Could someone tell me the diameter on both of them? Thanks.jorge.

I posted here because this is the turbo and related components forum. Feel free to move it to the right forum if need t.Hi everyone. My question(s) is in regard to the punishment racing intercooler cfm and the ETS street/strip intercooler cfm.Punishment racing bar and plate only. is...

This is a question that i had for some time now. I know that they are much more aggressive than the 272s and because of it, along with valve float and all that. A set of stiffer springs and retainers are needed. My question is, why is it that tuning is a must when installing 280s.?? Isn't it...

Hi guys, whats going on!! Well I search for this but didn't find anything, so here is goes. Has anybody with an aftermarket exhaust experience a wierd and high pitch noise when driving over puddles of water?? This is the second time that has happend to me. Today on my way to work, I drove...

Hey guys hows it going!! I have a quick question. Upon installing my new 3inch turbo back ex. I accidentally kinked the water line that goes to the oil cooler. Its a small cut that it has. My question is: Whats the best and most secure way to repair it?? Other than replacing it.Thank you...

Hi everyone whats going on!! Well, I have a quick question about posting and I just thought I ask here, since this is a non performance post. Where can I post about a vendor or shop? Asking information about them. Reporting them. Positive or negative feedback. ETC.I want to make sure...

Hi guys whats up. Well I have a quick question. Has anybody tried to fit the 2g megan DP on a 1g? The reason being is that i might be able to buy a 2g dp from a friend of a friend for about 70 dollars and wanted to know if it would fit. I did the search and didn't find anything. I Did read some...