All parts are best offer.2g Evo brembo brake conversion kit. These brackets will allow the installation of evo brakes to stock 2g knuckles. You can search the forum for instructions. Been on my shelf since I purchased them. - sold2g gsx front brakes w/ brackets6 bolt oil pickup with...
Working VW vacuum pump with bracket. Mounts nicely one the firewall below the injector resistor pack on a 2g.
$45 shipped with PayPal fees
812-229-4023
1450cc injectors comes with sheet from fic where they’d been flow tested with newer seals. $220 SOLD
1150cc they’ve been cleaned by fic and have newer seals, lost the data sheet. $200 SOLD
Black hallman mbc $55prices include shipping and PayPal fees.
812-229-4023
FIC 1150’s. They were just cleaned and flow tested this year by FIC. Found a deal on a slightly larger set so I no longer need these. $275 shipped/PayPal fees included.
picked these up used a few years ago, previous seller listed them with the marks shown. I didn’t think they looked bad so I bought them and I’ve ran them for 2 yrs no problems. Lobes are perfectly smooth to the touch. No deep gouges or anything like that.
$225 shipped obo
812-229-4023
Everything is OBO, please refer to flat rate shipping boxes when including shipping rates with your offer. More stuff you buy cheaper shipping will be.
812-229-4023PTE 880 injectors, newer seals
Gm 3.3 bar mapOEM
1g coils
1g nt intake manifold
6 bolt topline oil pump, BS delete. Less than...
Greddy style eBay intercooler. Comes with upper piping, where you have to buy it separately on eBay. IAT bung has been added and IAT sensor w/ pig tail is included. 1g bov flange has been modified for a real Greddy Bov. Does not come with BOV, could be added if buyer wants it. Kit has less...
6 bolt 100mm crank from a g4cs. Measured rod journals to be approx 1.771 and mains to be 2.244. Wear marks are pictured. Not sure if they can just be polished out or if it would need to be cut. Can provide more pictures if needed. $150 + shipping obo
812-229-4023
Just got a new car, parting out my 95 and getting rid of some parts I won’t need from the new one.AEM EMS v1 $225
98-99 black box ecu $100
Apexi power fc $225
HKS evc 4 boost controller $75
AEM Fpr + install kit $100
Samco red 2g upper and lower radiator hose brand new never installed $60
Gm...
97-99 automatic engine wiring harness. This is an extra one I have laying around I don’t need anymore. Has a couple connectors with damaged clips, and had the cas cut off to wire in 1g sesnor. $165 shipped in the US.
Is it possible for an oil pump to physically wear out?? I've also seen some high volume oil pumps for sales does anyone know what they have done to make it high volume? I have low oil pressure and i have checked everything the only thing that i could think of is my oil pump must be wore out...
I just swapped my 7 bolt for a 6bolt and since the swap was done my stock oil pressure gauge has been low. Now i replaced every gasket and seal in the engine prior to putting it back in, no oil leaks at all. The only thing i can think of is i reused the 1g oil pressure sensors on the oil...
I am getting ready to put in my 6 bolt and i have a question regarding the 1g cam sensor. Do you have to have some sort of logger to install this and get the car running correctly? I read what RRE has to say about ajusting the baseline timing, but i was just wondering if there was anyother way...
Ok I removed the rear b/s and wanted to keep the front one in so i didn't have to tilt the engine at a wicked angle, but once i got the car all back together i developed a oil leak shortly afterward. To make a long story short i have an oil leak around the front balance shaft sprocket because...
I just got a good deal on a 14b and wanted to replace my t-25 for the time being. I currently have the following mods:all the free stuff
K&N intake
2.5" exhaust w/ straight through cat
1G bypass valve
boost gauge & manual boost controllerOnce i get the 2g install kit should i go...
Just wondering if anyone has tried these vavles off ebayhttp://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&rd=1&item=7906955574&category=33621&sspagename=WDVWThey say the brand is EPN.. anyone ever heard or used these?Thanks
I recently bought a head that had the timing belt break and smack the valves. I removed all the valves and upon inspection of the guides i noticed a few of them were cracked at the bottom. Once I cleaned it up I brought the head to a local machine shop to have them look at it. The owner of...
I have read the instructions on road race's web site and have a question. Is it possible to use a non-turbo intake manifold & throttle body. I know the throttle body doesn't have a mounting point for the elbow.... but if i could make and elbow to connect to my upper intercooler pipe would it...