The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support ExtremePSI
Please Support STM Tuned

Search results for query: *

  1. Jacolu3

    Ready for 9s

    I'm using a pedal from a 2006 mitsubishi eclipse. I got it pretty cheap on eBay.
  2. Jacolu3

    2G rear tailgate thermo formed poly-carbonate window (1 window)

    I did not sand down the clear coat on my carbon hatch. I just cleaned the surface and used a lot of 3m fast cure auto glass urethane and haven't had any issues in 2 years.
  3. Jacolu3

    Ready for 9s

    Did a little upgrading over the winter Haltech elite 1500 with a bosch 68mm DBW throttle body Kiggly 12 tooth crank trigger Magnus intake manifold and a haltech IC-7 dash
  4. Jacolu3

    Ready for 9s

  5. Jacolu3

    Ready for 9s

    It wasn't that bad. With the ohm racing fuse box relocation wiring harness it was pretty easy. Took about a day
  6. Jacolu3

    Drive By Wire - Haltech How-To

    I ended up cutting the mounts off the pedal so it would sit flush on the firewall. I used one of the factory studs and a rivnut on the bottom. Worked out pretty good.
  7. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    Well the haltech has a plug and play adapter which makes wiring very easy. And haltech has lots of tech info on the web and they are very helpful over the phone too.
  8. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    So I just finished doing this with a haltech elite 1500. I don't think ecmlink would be capable of doing this. The pedal gets wired in directly to the ecu and the throttle body also gets directly wired into the ecu. They actually don't get wired together. The pedal will have 2-5v wires...
  9. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    I attempted to mount my 3g pedal this weekend and I didn't like how it wasn't going to sit flush on the floor boards. I ordered a 1" thick piece of aluminum that is the same width and length of the pedal. I will have to try to fab something up with it so the entire pedal has a flat surface to...
  10. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    I'm planning on mounting it this weekend. I'm going to try use rivnuts to mount it. If it works out good I'll post some pics this weekend
  11. Jacolu3

    Drive By Wire - Haltech How-To

    I plan on mounting mine this weekend with rivnuts. If it works out I'll post some pictures
  12. Jacolu3

    2G rear tailgate thermo formed poly-carbonate window (1 window)

    I've had mine for almost 2 years and still looks brand new. I have mine installed in a carbon fiber hatch and would highly recommend it.
  13. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    This seems to be right. The colors match for 5 of the 6 wires. Thank you!!!!
  14. Jacolu3

    2G Looking for 2012 pedal wiring diagram for DBW

    I'm switching to a bosch dbw throttle body with a 2012 eclipse pedal assembly. I have the factory plug but I can't find a wiring diagram for the pedal.I was wondering if anyone has a wiring diagram for a 4g eclipse or knows the pinout for the pedal?Thanks Brian
  15. Jacolu3

    Drive By Wire - Haltech How-To

    Is there any info on the wiring of the pedal and throttle body?
  16. Jacolu3

    2G Evo rear differental axle install question

    Cool thank you for the help!!!
  17. Jacolu3

    2G Evo rear differental axle install question

    So you would say that they are in all the way?
  18. Jacolu3

    2G Evo rear differental axle install question

    So I just had a rear dif built with an evo lsd for my 2g dsm. I purchased dss stage 5 rear axles with evo inner cups. I installed the axles and the dif today and I'm not sure if the axles are in all the way. I push them in until they feel like they are maxed out and I can't pull them out...
  19. 2g dsm driveshaft shop rear axles 800hp

    Question by 'Jacolu3' on classified ad '2g dsm driveshaft shop rear axles 800hp'

    Price is slightly negotiable
  20. 2g dsm driveshaft shop rear axles 800hp

    Question by 'Jacolu3' on classified ad '2g dsm driveshaft shop rear axles 800hp'

    This is the stage 4 driveshaft shop rear axles. These axles use the stock wheel bearing. They are a direct replacement
  21. 2g dsm driveshaft shop rear axles 800hp

    Reply to question by 'Jacolu3' on the classified ad '2g dsm driveshaft shop rear axles 800hp'

    I'm going with an evo rear dif so I need different axles
  22. 2g dsm driveshaft shop rear axles 800hp
    Sold

    For sale 2g 2g dsm driveshaft shop rear axles 800hp

    2g dsm LSD Driveshaft shop 800 hp rear axles brand new. Current wait time is around 10 weeks from all vendors. No wait time Brand new, never installed. Comes with axle nuts. Retail price is $1499.96 plus shipping with approx 10 week wait.Selling for $1250 shipped with no wait.Mitsubishi...
    $1,250.00
  23. Jacolu3

    Drag Race Build My 2g dsm second build, this ones going smoother

    No problem!!!! Can't wait for Saturday!!!!
  24. Jacolu3

    2G Drivers side axle not going in

    Couldn't have done it without you bro!!!!!
  25. Jacolu3

    2G Drivers side axle not going in

    yup that's the culprit.
  26. Jacolu3

    2G Drivers side axle not going in

    So I figured it out. I also had the t case rebuilt and had the center billet piece added on and one of the bolt heads was a little too big and the half shaft was hitting the bolt.
  27. Jacolu3

    Ready for 9s

    I supplied most of the parts so it was pretty quick. It was about 3 weeks for them to finish it. I'm running the oem 5th just because I don't drive the car on the street and I don't shift into 5th in the 1/4 mile
  28. Jacolu3

    2G Drivers side axle not going in

    Ok I'll have to go at it again. I appreciate your help!!!
  29. Jacolu3

    2G Drivers side axle not going in

    The bolt holes are about 1" away. And my shaft is sticking out much more than yours
  30. Jacolu3

    2G Drivers side axle not going in

    I'm having trouble getting my drivers side axle into the tranny. Its a 97 gsx and just had a ppg dog box built with a front quiafe lsd and a center spool. For some reason it won't go into the tranny all the way. The intermediate shaft has no c clip so it should slide right in but stops about an...
  31. Jacolu3

    2G Help with volk 2g subframe bushings...

    I removed outer ring when I did my volk rear subframe bushings. I'm pretty sure they won't even fit with the ring still in. I actually put them in the freezer over night to help shrink them a little to make the install a little easier.
  32. Jacolu3

    Ready for 9s

    Just got my tcase back from Boostin performance with the 300m output shaft and billet center section. She sure is Purdy!!!
  33. Jacolu3

    Ready for 9s

    Rrt in Connecticut built my dogbox. I supplied the ppg and a few of the parts and they did everything else. The twin disc I got from tmz performance. They sell it for a ppg in a 2g. I'm pretty sure it's meant for an evo 8 and with a 7 bolt flywheel. It wasn't cheap but he sets everything up and...
  34. Jacolu3

    Ready for 9s

    Either here or pm is cool with me. I'd be happy to help with any questions.
  35. Jacolu3

    Who's running boostin's KDN shifter?

    I was probably one of the first ones to receive it for a 2g and have it installed. I do have the lockout option. I had to cut my center console where the cigarette lighter usually is to fit it. I just relocated around the side with an aftermarket one. My first advice would be to watch the 3...
  36. Jacolu3

    Ready for 9s

    Forgot to post my carbon fiber hatch with lexan
  37. Jacolu3

    Ready for 9s

    I do have upgraded rear axles so hopefully they can take some abuse. The only rear end dif option I know of is a 3k rear dif and I'll have to wait until the stock one goes before I jump to a 3k
  38. Jacolu3

    Ready for 9s

    Still holding up great. I haven't driven the car yet with the ppg. Waiting on my tcase to be built before I send it.
  39. Jacolu3

    Ready for 9s

    Quarter master twin disc 8 leg installed along with my ppg dogbox with a center spool and a front quiafe lsd. Ready for 9s
  40. Jacolu3

    Ready for 9s

  41. Jacolu3

    Ready for 9s

  42. Jacolu3

    2G Ppg with spool and quiafe lsd question

    Great info like always!!! Thanks Tim!!!
  43. Jacolu3

    2G Ppg with spool and quiafe lsd question

    So I just had a ppg dog box built with a spool and a quiafe lsd. I'm about to install it and I went to spin my input shaft by hand and the output shaft doesn't spin. On my old tranny i was just running a 4 spider center and when I spin the output shaft the input shafts with it. I also tried...
  44. Jacolu3

    ECMlink PiLink - Owners Thread

    I used an inline fuse to be on the safe side
  45. Jacolu3

    2G Vamous Design Fuel Cell! Help

    Yeah I used some aluminum strips and made some brackets to mount my pump and filter in that little slot. It was a tight fit, but I made it work.
  46. Jacolu3

    2G Vamous Design Fuel Cell! Help

    Not the best pictures but this is how I did mind
  47. Jacolu3

    2G rear tailgate thermo formed poly-carbonate window (1 window)

    Yes I just used professional grade 3m window urethane. I'm going to check it this weekend for leaks
  48. Jacolu3

    2G rear tailgate thermo formed poly-carbonate window (1 window)

    Installed mine over the weekend. Perfect fit!!! Glad you made this happen!!!
  49. Jacolu3

    2G Vamous Design Fuel Cell! Help

    I bought the gst fuel sending unit and he includes the wiring info in the directions. Worked perfectly for me with the gst sending unit.
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top