Please share back what you find out and what polarity reverser you use if it works. I wonder if you are going to run into the same issue I didn’t with the lights being sim once both LED lights were installed
I’ve seen them, but never tried them personally. I can’t decide if the issues I was experiencing with the lights I tried before are due to the lights or if there is something weird with how the headlight circuits are wired in these cars (or if there is just an issue with my car).Hopefully...
I believe your issue is the fact that the car switches the ground connection from the factory (“common power”). However, most bulbs these days switch the power side to toggle the high low beam (“common ground”).There are conversion boxes out there that would make this common “power” to...
Not sure if it’s similar or not, but I have noticed on hot days that if the car sits hot for like 30 mins or so, it will start, but idle badly. If I give it a little bit of gas for a few seconds it tends to clear it up. Car is completely stock fuel system wise. I always kinda figured it was the...
Good to know. I’m planning on hopefully only having to replace the master at this point. Finally was able to get it out last weekend for the first time this year just to have to put it up again until this gets sorted. Damn the luck
It’s not common for there to be an issue with the booster is there? It’s most likely just the master cylinder? Brakes felt fine, it was just the light on the dash that prompted me to look. It looks wet right where the master cylinder and booster mate. Just trying to have everything that is...
So I finally got my 90 Talon out for the first time this year. I am finding the the e-brake light is staying on no matter if the brake is engaged or not. Are there any quick thing to check so that I can get the light to go off?90 Talon FWD if that matters.Thanks in advance!
Thanks... I will try reaching out to archer then. I’m still using a side mount, but would like to replace the 30+ year old rubber pipes for something better if possible
yeah... I just experienced a weird issue where the light would be at like half power when two LED headlight were plugged in. One halogen and one LED was fine. Not sure if it was just the lights I was trying to use or not. I imagine that a simple relay harness would fix the issue, but I haven’t...
Please let us know if you run into weird wiring issues when trying them. That is what prevented me from getting mine installed last year and just didn’t have time to troubleshoot further.
I am looking into those as well. However, I think you will still have to tackle the issues I stated above to get them to work.I run Morimoto bulbs on my daily and really like them a lot
Sorry... forgot to post back hereI ended up putting the car back to stock headlights since I ran into a few issues and didn’t have time to investigate further since I wanted to start driving the car to work.The wiring has to be modified to get these to work. I swapped the pins around to get...
Not sure if it is true or not, but I think they did just improve the bushings when comparing the 90 and 91-94 bushings. I think we used the updated bushings on my car for the last rebuild. It was years ago though, so I can say for 100%If we can get confirmation that this set will work with a...
I played around with LED headlights a little bit last winter. Here are the two issues I saw (at least in my 1990).1. The wiring harness on the cars are reverse polarity from what you typically see. These cars have a common "positive" and it switches the "ground" leg depending on if you want...
Thanks!... ordered one just for the future. Hopefully someone comes along down the road to make a suitable replacement so we can keep these cars on the road
My car does the same thing. It goes away as long as I leave one hand on the wheel, but it always bothers me.Would appreciate a write up if you figure something out!
Great.... once again the 90's being the bastard children of the DSM world. So I assume the only real possibility is to have an actual 1990 intercooler re-cored if wanting to stay side mount?
Please keep us posted if you are able to figure this out at all. Mine has been doing the same for years. Light comes on the stalk, but immediately goes back out again.
I would be interested something like this as well. Are there actual differences between the stock FWD and AWD intercoolers or differences between 1GA and 1GB?If this is something you are willing to look into, I have a stock 1G intercooler laying around that could be lent out to see what could...
Is anyone aware of any direct hard pipe intake piping that would mount right up in place of the stock pieces? I am looking for something that would not require modification to BOV flanges or anything like that and am planning on staying on the stock intercooler. Car is a 1990 since I think the...
Unfortunately, I do not have a way to measure the candelas. I have been thinking about trying these bulbs for over a year, so I figured I would give it a shot.I do agree... they are interesting looking. From what I can tell, the lights on either side of the low beam projector are responsible...
I was able to find a few mins to get one side installed tonight (Pictures attached). Will be working on getting the passenger side installed tomorrow.The bottom two "projectors" are for the high beams, so they are not supposed to be on in the pictures. I personal don't think they look as bad...
I can post some pictures once I get them fully installed. After fighting the wiring problems all day, I called it quits once I found the solution. I was not in a rush since it will still be several weeks before I will get the car out due to the weather. Give me a few days and I should have at...
Figured I would update this thread...After initially asking the question about the LED headlight conversion and trying LED bulbs in the Hella conversion housing, I was still not really happy with the results. After that failed attempt, I just left the car as is was for the rest of the year...
Thanks everyone.... looks like the projector style LED's are the way to go. I will take a look at what is out there and try a few of them. Seem like the 1ga headlights and fog lights are more difficult to get anything modern to fit/work. I found what appears to be 4x6 led projector replacements...
just curious to see why other people have had luck with.... has anyone switched to LED bulbs in the fog lights (oem)? I am specifically asking about the 1g fog lights that use a H3 bulb.Seems like the market is flooded with cheap bulbs these days...
It doesn’t matter if the individual components were balanced, it can still be out of spec once the whole rotor assembly is assembled.100% get the whole thing balanced