hey so while my car is down in the process of being rebuilt im thinking about doing an engine harness tuck. i came accross this on an evo forum and im wondering if dsms have the same set up pretty much when it comes to not actully having to cut wires up and such, ive never done a wire tuck or...
hey my name is Matthew, I've had my eclipse for a few years now, done a few things to it like the basic intake/exhaust boost controller (after maintenance of course :boring:), but recently I've finally gotten it to a point where I'm ready to start building it, also happens to be about 20 miles...
So long story short my old transmission went out. So i bought this one from a guy on Facebook he "guaranteed" it was good . installed it and this is whats happening its like the clutch is sipping but its not I've taken the trans off once to make sure it wasnt the clutch, and it never had any...
Hey guys i have a really weird problem with my 1g, one day my radio just shut off and wouldnt turn back on, so today i pulled it out checked the fuse on the back after checking the fuse by the kick panel and it was good so i checked for continuity on the radio ground. it was good so i checked...
I'm thinking about switching to a water to air intercooler set up on my daily driver GSX. I read some places that it would be bad for a daily set up but i don't see how that could be true if you have a good heat exchanger set up and a good pump moving the water. I'm just looking for someone with...
So to make a long story short the board on ic110 is bad and i need to know where i can get a new one. if i can find an ecu for parts i know i can use that but i would like to buy one new if i can. does anyone know where i can get parts for the ecu? its a 92 awd. any help would be awesome thanks.
i am in the process of getting all the parts to delete the abs in my 1g i have the non abs proportioning valve and the lines from that to the master cylinder. all i need now is the line to the front brakes from the proportioning valve and im wondering if anybody knows how long those lines are...
I have been searching around for a little bit now and i cant seem to find a picture of polished 2g talon swirl wheels has anyone done it or have a picture? I'm thinking about polishing the wheels i have on now. :hmm:
I am about to clean my K&N filter and i dont have the recharge oil from K&N so im wondering if there are any alternatives of the oil i was thinking about using some seafoam. anyone have any input on this?
Hey I'm wondering if anyone has used the energy suspension sway bar bracket kit? Did it help at all with handling? My sway bar bushings need to be replaced so bought the energy suspension kit and just looking for some first hand experience with those.
hi im having trouble with getting my drivers side window to come up straight i looked on vfaq and i found how to repair the switch, did that and now the motor seems to move a little better but it still get sideways trying to come up i cleaned and greased the runners. is there something i can...
hi i tried to make a usb datalogging cable off of this thread
http://www.dsmtuners.com/forums/articles-tuning-ecu/424006-easy-way-make-1g-usb-datalogging-cable.html
i cant get my laptop to recognize the wire when i plug it in im not sure what im doing wrong. if someone could help me i would...
hi im wondering if this is everything i need to datalog on a pc i dont have a palm nor do i want one. does anyone have any experience with this?Mitsubishi DSM OBD1 Scanner Cable Software USB to 1g 12 Pin Aldl Direct | eBay
I'm in the process of trying to drill out exhaust manifold studs and the dipstick is in the way. I alrea?dy took off the one bolt I can see is there anything else or does it just pull out
I'm about to start putting on my fp race manifold and I also bought exhaust manifold to head studs I'm wondering if anyone has advice on removing the old ones. Any advice would be great haha
Just like the title says I just got a new exhaust on my gsx and the nuts that connect the downpipe are backing out. My question is will red locktight be enough to hold them on?
Hi I'm working on making a cousin gauge pod for my pillar I'm wondering if anyone knows the exact color or best matched paint to repaint it three same color as stock
so i just bought a new 3 inch downpipe and tubular o2 housing and an fp race manifold as well as an aem wideband... all yet to be installed because im wondering how far back on the downpipe am i supposed to weld the bung for the o2 sensor. ive heard 18" down the downpipe and ive also heard 36"...
okay so i have a check engine light on and i recently got a new ecu that was rebuilt. the code is 43 for the egr i dont have one and im wondering if there is a way to get the light to go away.i found this and im wondering if anyone has any expericence with this working...
So on newer cars i like how you can have the key out of the ignition and have the stereo stay on untill a door opens, so i figure why not do it on a 1g.. im just looking for advice about how to do this. any help would be awesome thanks! :rocks:
so not to long ago my car would not start so i go to pull out the ecu and find that my ecu is blown along with the isc so i replaced both thinking that that would fix it but when i tried to start it again it still wouldnt so i looked at the ecu again and one of the caps blew or leaked.. my...
i think my tps sensor is out it is a 3 pin sensor i can only find out how to test the 4 pin one. and would that sensor being out cause this to happen on the ecu? any help would be great thanks alot.
hi a friend of mine just got a front wheel drive tranny rebuilt put it in and everything but it grinds and wont go into first gear with the motor shut off it shifts into all gears. help!!!!
im not sure if this is the right place for this but what do you think of these brakes do they seem worth it or not so good? it seems like a really good deal but i feel like im risking my life buying brakes from ebay :pray: has anyone tried these?Premium Performance SLOTTED BRAKE ROTORS FRONT...
i have a picture right here it was running the other day i turned it off for about a minute started it back up and it had no spark it showed no signs of that before.after looking at the picture closer right in the middle there is something burnt and at the top left another thing burnt. now i...
hi i am wondering if i need to unbolt the carier bearing on the drivers side cv axle or if this will come off from here? if it will how do i get it out?
hey guys my oil presure gague is not working i just jacked up the car to do my cv and noticed that this blue wire is unplugged looks like it might be the reason does anybody know where it is supposed to goalso i am about to do my cv axel on this side is there any suprises i might run into...
okay so i was doing my valve cover gasket the other day and when i took the cover off i see on the left side by cylinder #4 on the intake cam its discolored does that mean a bad valve seal? i have a picture right here
so napa auto parts is at it again it looks like they gave me the wrong size pintle cap does anyone know if this size will not work.. and if it wont work do you know where i could buy one that is the right size? i have a picture the big one is the one napa gave me and the broken one came off does...
hi im having trouble figuring out where all the seals go there is the one plastic tip looking thing that i dont really know where it goes. does anyone know where a diagram of what place they go on the injector is? i have a picture the one im not sure about is the plastic tip thing..
i have done a little research and i havent found a conclusive answer.. when i start it, it seems like it doesnt idle right untill it gets up to temp but when i am in traffic or stopped it overheats the fan doesnt kick on i think.. does that mean that the sensor is out? and if so is there a way...