The deadly combinations is killing your ET/MPH. I would guess mid 8s with your current boost level no problem. Hope you make it to the SO.

I’m curious why you didn’t go with the bigger turbine housing (1.15 divided)?Any feedback on the new turbo yet?

Go with the newer EMS like the Fueltech 450 or 550.

Congrats on new PB! 8s is right around the corner.Are those the new style Slipstreams? 15x7?

Congrats! Huge jump from the BW 63mm. Plenty more room to go.What boost and nitrous was that run? Dyno numbers? Also, what base fuel pressure?

Minimum usage FIC 1800cc low-z injectors. Great for secondary. Sent in for cleaning and flow test. Still sealed in the package from FIC. Comes with new upper/lower injectors seals and flow sheet. $300 shipped.https://fuelinjectorclinic.com/dsm-evo-1-9/IS126-1800

I have a mint condition PTE 6870 for sale. I upgraded to bigger setup and no longer needing it. SOLD!Some details...Precision 6870 Gen2 T4 Divided 1.32 A/R: - Original owner - 10 passes (7 - 1/4 mile, 3 - 1/8 mile) - Less than 200 miles of street use - Always filtered (air filter and oil...

The reason I could think of is to ensure the Check Ball that is sandwiched between the reaction shaft support and oil pump housing is properly aligned. Another reason is for the ease of installing the oil pump into the transmission housing.I tried using the “eye balling” method without...

L19s for 6 bolt

Kiggly High Pressure valvesprings. Has about a dozen passes and less than 300 street miles. SOLD!L19s 6-bolt. Used in good condition. $150 shipped.+ PP fees.

Perfect fitment and worked as advertised.

There were some info and pics from another member on making the 3kgt rear diff worked on 1G rear subframe. If you can’t find it, lmk. I might still have it saved somewhere on my PC files.

Looked like a completed and quality kit for sure. I wish this kit was available years ago when I swapped 2G stuff into my 1G. I had to piece together parts and played with fittings hoping everything aligned.Although I’ve never experienced any issues with the TCase, I never thought about the...

Get a new Bosch Saturn alternator and pig tail plug. I’m getting 15.5-16.3v at idle. I’m running mechanical pump so that helps. Single pump amps draw shouldn’t be too bad though. I’ll report back once I get more testing.

Magnafuel MP-4303 - used but good working condition. $325 shippedBAP 30 amp - used but in good working condition. $125 shippedFIC 1550. Just came back from cleaning and flow services by FIC. Still in sealed bag. Flow sheet included. $350 shippedPP fees not included.

Can you share the link or contact?

Thanks! Will place the order soon.

Which application work for my setup?1G car with 2G aut trans, Hurst Promatic shifter

Stick to the 5 frictions if street/track or Kiggly billet. The disks are very thin on the 6 and won’t last as long with extended street miles.My Kiggly 5 frictions lasted for 3-4 seasons on street/track car running 6466. It held up fine when I upgraded to 6870. However when I did trans...

I would recommend you check out another dsm member setup. His mechanical setup seemed to work great.

Having a brain fart today but what’s SPDT = ?

You should offer oem extra capacity pan with extended oil pick up.

You probably don’t need it yet. I would do the billet transfer gears first follow by billet front and rear. Inspect your oem saddle and pay attention to the wear pattern.I upgraded mine not because I need it yet. It’s because I’m doing a refresh along with other billet parts upgrades. While...

SOLDhttps://kigglyracing.com/engine/billet-12-tooth-crank-trigger-sensor-kit-v3.html

Solid trans setup that should be good for 8s. It’s as bullet proof as the next weakest link. Anything can be broken if you abuse it or not properly put it together.You can have your gears and other metal parts go through cryogenic and shotpeen treatment. I was told it could last up to 20%...

Billet 12-Tooth Crank Trigger Sensor Kit - V2. Trigger wheel was mounted but not used. Everything else is 100% new.$175 shipped + PP fees

Forced Four SMART 100.1 Shiftbox + SMART Handheld with the latest software update. Still installed in the car. Harness shortened for clean install. Like new.For details: http://www.forcedfour.com/smart100_1.htmIncludes: 1. SMART 100.1 Shiftbox 2. Wiring harness 3. SMART 100.1 RED Handheld...

Car and overall plans looked good. What EMS are you running? I noticed you are running the 12-tooth trigger so it isn’t Ecmlink.Wish an Evo shell like yours was available 2 years ago when I swapped over to another 1GB shell.

2 sets:1st Sets: These gears have been shot-peening and has around 10-15 track passes in 1/8 mile. Inspection completed no cracks, no issues. Doesn’t not come with bearings. Upgraded to billet gears. $250 shipped.2nd Sets: Transfer gears AWD Auto trans with 65k miles. Stock, no mods...

1G Fluidyne radiator with 10” slim fan. No issues cooling. $100 + shipping12” SPAL HD motor High-flow slim fan. SOLD.11” SPAL slim fans. $50 shippedInbox me for pics please. Thanks.

1G Mitsu rebuild alternator 140AMPS. Less than 25 miles. $100 shipped. IM for pics.

Any status update on 1G tubular rear subframe kit design?

Congrats on PB! It came a long way and lots of hard work. It definitely has more left. I loved the 6466. Keep up the good work!

Im using Bosch SR4166N starter on my 1G AWD with 2G Auto trans setup.

This cold air intake came off my old setup. It is best used for bottom mounted manifold. It would put the air filter right at the stock SMIC location on a 1G. Aluminum 4" diameter. Comes with K&N air filter, coupler and T-bolt clamps. Used. SOLDJMF sparkplug cover. Used. $60 shippedJEGS...

Did you check the dimmer knob? I had an “ah-ha!” moment before and it turned out to be this.

Cams are still available. $450 shipped!

Pics added...

Kelford 288/280 Camshafts: Mitsubishi Eclipse 90-99 4G63. $450 shippedKiggly Racing "RACE ONLY" Beehive Valvesprings. SOLDBoth have less than 100 miles.Please cover the fees. Thanks.

I would find something more reliable so that you don’t have to mess with it all the time. Invest your time and resources on school and get out ASAP. :)

Selling new in the box front and rear drag Brakeman drag brake kits for 2g 95-99 AWD. I didn't want to sell these but things have changed. Selling for $2500 shipped... That's nearly $700 less than if purchased through STM. Feel free to text me at 803 707 five five 8 five with serious inquiries...

JM Fab kit

They are about an hour from me. I called to place an order but he said he lost the windows measurements. Interesting...

Go for the 220amp unit and Kiggly's pulley and post feedback. :)

Congrats on your new PB! Looks good Aaron. I'm interested to learn more about the new FF front case setup.

Good choice and good luck at the WCF this year! :)

Why not go with 3.5"? I run 3" aluminum exhaust with the same muffler. I should've went with 3.5".What kind of CF hood is it?

Looks good. I like the tinted look much better.

What ducting material is it and where did you get it? 10-15* drop is really good.