So I replaced my clutch in my evo 9 installed an act lightened flywheel, hd pressure plate and a street disc. Install was straight forward everything seemed to go fine. Went to drive the car it felt different a little harder to get into gear. So I went through the clutch adjustment procedure...
car-cannibal how do u like the strokinator? Did you or know anyone that ran the Draginator 9.5”. Does anyone know what kind of power a stock restall can handle? I’m new to the auto world and this will be my 1st auto car so sorry if I repeat myself. I plan on being around 800 plus hp so just...
I’m looking for a high stall converter guess I should have specified that. I found someone selling a sinister draginator anyone have any experience with this converter
Thanks the welding is not the problem I just didn’t want to do through all of the fab work and not be able to pass tech. I knew I read it somewhere but have not been able to find it again.
I bought a shell with a Ms cage in it and want to build a tube front end. I would like for it to be a extension of the cage. I bought a bender and it came with a 1 1/2” die. The cage is bigger tubing 1 5/8”. My question is would the be a problem with track rules we’re adding smaller tubing...
I have a 2.3 I know it’s not everyone’s favorite but it’s what I have for now. I have a 6466 and not sure what cams to use I’m looking at the kelford 272 or 280 from what I have read it kind of gives mixed feeling on witch would be better. Some say 272 bc strokers are not reved out as far...
I’m picking up a auto swap this weekend but don’t think it comes with intermediate shaft is there a way to make the manual one work or do I have to hope to find one thanks
I have read many treads about 1g and 2g using evo valve train parts. I have recently acquired a 06 evo and have a spare set of dual valve springs and retainers from my 1g front what I have read is everything from a evo will work on a 1g or 2g but nothing is discussed about the way around. I’m...
Thanks for the advice. I have been carefully going through the chassis harness and eliminating what I don't want. I have ordered relays, universal fuse block and a few other things I will update with pics when I get a chance
http://www.hotrodcoffeeshop.com/forum/viewtopic.php?t=72Found these 2 good info that schematic show you exactly how to make your engine harness independent for a swap car I'm definitely going to give it a try.
I want to keep it street legal for the occasional cruise. I want to use something like this.. I want headlights, taillights,flashers, wipers and maybe keep power windows. From the videos I wanted you only need to power a few wires to get the motor running. And I might run the fuel pump and...
So my car was flooded and completely under water. I have the entire interior striped out and am looking to do full race car wiring and eliminate everything not needed. Just looking for people that have already done this. I want to use a painless style universal chassis harness ,thin out the...
Really debating on picking up a 6466 Gen 2 turbo. Just wanted to see who's running them and what kind of power and times you are putting down. Also on what turbine housing your running. I'm considering a .82 v band thanks in advance.
Bumping. I have always wanted to try a compound setup not sure it's worth it but recently my car was completely under water due to a flood so the it has to come apart anyways. I have a 68hta and a hx55 laying around does anyone think this would be a good combo. I have been eyeing up the...
Thats the new vs old fittings. There were both -10 barbs now there 23mm pan and turbo. The fitting is bigger than the hole in the turbo. The pan fitting is in the same location as stock just way bigger. I guess i either hurt it or bought i bad turbo.
Ok guys I made a new oil drain a few weeks ago, its 23mm about 7/8 big. I had to sort out my new sd setup I'm new to tuning myself. So I ran the car for a few mins today and it smoked out my garage were i thought the neighbor's might call the fire department. I ran the car around 1500 rpms...
The map sensor is hard wired not pnp. I checked the wiring a few times its correct. Red 5 volts, black is ground and the blue is putting out 1.1v with key on.
I added baro to the displayed values on the log you can see baro its just faint its under knock. Whenever i click on ve from log screen...
I switch to sd and my ecmlink is not seeing the map sensor. And car is running super rich. I'm pretty sure i have everything set up right i have done alot of searching the last few weeks. Hopefully someone can give me so insight.
I checked the wiring 10 times and from my tests the map sensor...
Hi guys wanted you opinions. I just put a brand new hx40 on my car and theres a extreme amount of oil coming out the exhaust. 1st start up i had no restrictor but since then i added a .080. I have a -10 barb return fitting on the turbo and pan from extreme psi. I contoured the flange that...
I have a set of fuel injector clinic 850cc injectors that I bought off here but never used. I was told they were pulled from a running car. SoldAlso have a 1g maf harness adapter and evo 8 maf. Harness adapter is brand new from ecmlink. $150 obo
I have a chance to buy a low mileage engine. The seller says it has cams from a sIowboy stage 2 head package but has no specs on them. Wanted to know if anyone might have some insight on what cams they are. I tried searching but has no luck thanks
From what I have read you guys are the king of holsets. So can someone please tell me where i can order a new hx52 pro or not from. It would be greatly appreciated thanks