Thanks to clarify the pilot bearing and I even wrote changing the rear differential and about the half shaft but later on figured it was a FWD and erased all that, some how I passed the T case.Good catch.
You don’t need the ECU, nor to make a hole on the firewall, the hole is there all ready and has a plug, just remove the plug and you are all set. There is a TCU in the automatics but is not needed on the standards, so you don’t need a different ECU, just use yours.However, you need the...
Selling a 2g AWD Fuel sending unit with a Brocken fuel line outlet, this is ideal for AN Conversion, also it doesn’t has the connector from the gauge to the unit, but it has the wires intact with pins, all whaat it needs is just the connector itself, you can depin your connector and swap it...
Ok you have all new but is all working?,Ok this is how things gets easier to find.
Check to see if you have fuel, you can hear the fuel pump kicking in when you turn the key to the on position (no cranking) it will turn on for 3,5 seconds, then it will turn off, if you don’t here this noise...
I don’t know about the Mighty Max MPI, but what makes you think is bad?, is the clicking noise coming out of the Mpi relay?
Do you have run an overall test to see what is getting or what not, like fuel or spark, I know it was running before but things can happen while working on it.
Does the...
Does anyone has contact Brandon lately ?My rack has the same play and that’s only moving the shaft on the shelf, it has a lot of play with no force on it, I know once installed it will be worst.I Email him last week and still no respond.
If anyone knows or have the info to contact him...
Unplug one injector while is running and check on the leak, do the same process on every injector and the leak should stop once you unplug the bad injector.
On the AC compressor wiring. All 3 wires come from the engine fuse box. Take a look at the compressor, is there a little plastic sensor cover at the compressor with 2 wires coming out of it?, if it does has the sensor then sure all wires come from the fuse box.One wire comes from the fuse box...
Not much of update but Today the end clutches show up, so I will be installing them in a couple of days, I hope to have time next weekI will update the thread once I install the end clutch.
Concerning to the shift knob,
I used to have that hard to shift feeling on my short throw and putting a heavy knob did the job, there is way, way less effort to shift and has a smoother shift feeling.
Good eye you have DUSTYBONER.O The pic angle makes it hard to be sure if the wiring is backwards, check/confirm the blue wire of the connector matches the yellow wire of the other side of the connector,
If it doesn’t match then that’s your problem as Dustybonner mention.Just to have it...
Are you loosing any coolant?.
You mention you have one fan and is keeping up but, is the fan turning on so frequently, or is it ON all the time?, Give more details so we can get to the problem easier.
I forgot to mention, I drove the car andI still feel the transmission acting up when putting into gear.I ordered a IPT end clutch, we’ll see if that cures the problem, besides the hesitation when puti y ito gear all feels ok, but like I mention earlier, I have no experience with auto...
Thanks I try to update the thread but now in my daughters hand, I won’t be able to work on it so often.
The screw caps are originals, I new that with my first DSM, it was a second owner and was unmolested in stock form.I used to go to the junkyard so often and get all of the caps and screw...
Update.
Is being a long time since I work on the car and today I took it off my daughters hands to do a maintenance.She called me saying the driver side door doesn’t opens from the outside, it only open from the inside,.I removed the handle and found an aftermarket still bracket ( the one...
Looks like the harness is all messed up, the problem gets worst which you are not looking for the problem (bad wire) but instead you are adding another line to source the current.Doing it that way and not getting results makes me think the bad wire is shorting some how and making the system...
What’s the total price on coating all the bolts including the sand blasting?I was thinking on buying a kit to do it my self but I would rather pay to do it and not equating my time which I barely have time to work on my DD.
Like DUSTYBONER said, it might be a bad connection.clean the battery terminals very well and jump wire the starter directly from the battery and see what happen, it should turn.
This thread is to old,However there is a vendor selling Chinese exhaust housings on eBay for cheap and they work fenomenal as replacement.Do a research here in tuners to find the source, so you get the one I’m talking about, there are some housings with the holes not aligning right and...
What’s the deposits amount? I didn’t see that in the first post, and/or when we should start sending the payment.Maybe it’s on the list to do and I’m all ready ahead of that:beatentodeath:
1/4 mile straight line, what is required?, I’m sure the helmet, but besides that is there any else like the car needs to have, like fire extinguisher or any other stuff for the car, any mods or safety stuff.
I wouldn’t do a starter kill switch, that’s being for ages and everyone knows how to start a car without finding the switch button, and that’s without saying if it’s a stick shift, it will start with a push.I would go with a kill switch to the ECU switch current, and using 2 or even 3...
Update.The car went to my daughter’s hand all ready, so she owns it now, but I’ll be taking care of her still.The last thing I did to it was, fixing the brake noise, it end up being the brake pad hardware, I fixed the door switch and the valve cover leak, I just tightened the bolts and it...
Yea It’s just the transmission that I don’t trust jet.
It’s being really good but in the morning when is cold, it takes a bit to go forward, or better say it goes but very slow, like if there is not much oil pressure and once it warms up is completely gone.I just want her to take care of her...
A little update.I bought new rear brake pad hardware to replace them, but it end up to be the Wronge parts, because was to late I couldn’t return them, so I took the time and inspect every single part and did notes some shiny spots where the pads were moving, so I bend the taps a bit to...
The throttle body gets the leak in the FlAV (internally), it won’t show on a boost leak, basically it leaks from the intake pipe to the intake manifold.Here is a thread in regards.
https://www.dsmtuners.com/threads/bad-fiav-what-do-i-do.366394/
You have a big leak, make sure the throttle body is not damage.I know it sounds odd but is the booster vacuum hose hooked up?, I put my 2c on a leak in the throttle body are
I just received a trucking number for the rack and it should be here next Thursday so looks like finally I’ll have it in my hands.For those with the powder coating option, you will get a trucking number soon IF, you haven’t received it yet.
First pic is for the noise condenser, here is some info so you know what it does and how it looks likehttps://www.dsmtuners.com/threads/part-question-pic-included.288714/the rest of the pics are hard to see it, you need to take a better pic of it and try to get the hollé sensor not just...
Is called Capacitor (Noise Condenser)If you go to first post, there are all the connector descriptions and just click on it and it automatically send you to the connector.
Wow I’m speechless, that came out very good looking tire well.I love it, I really enjoy a thread when there is a lot of passion involved.Keep it up bro.
Update.I changed the Ebrake hardware on both sides.Here are some pics for the viewers.I clean all the area and I can see there is no rust around the surface so that makes me opt for painting it and prevent future rust.I hate to just paint all evenly, I like to paint parts...
People usually hack the wiring when doing a 6 bolt engine swap., but if you have a 7 bolt then you don’t need any harness, just fix the one you have.Looks like the OP cut the wires weren’t using to make the engine bay cleaner.
The 95,96 uses two connectors in the same locations (like yours)...