The Top DSM Community on the Web

For 1990-1999 Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, and Galant VR-4 Owners. Log in to remove most ads.

Please Support Morrison Fabrications
Please Support Fuel Injector Clinic

Recent content by kanusky1990

  1. 2G Camshaft degreeing help

    Are you using solid lifters while taking the measurements? If you are using the normal hydraulic lifters, they will bleed down over time from the spring pressure and give you an inaccurate measurement. It sounds like that is what is happening when it changed from 0.040" to 0.047" while...
  2. Oil ventilation

    The vacuum from the intake pulls the water vapor, blow by, etc out of the crankcase from the valve cover.
  3. How to come up with a compression ratio?

    Hey,Static compression ratio is the ratio of the maximum to minimum volume in the cylinder (volume when the piston is at the bottom of the cylinder versus volume when it is at the top).This can only be changed by changing the physical components of the engine (crank throw, rod length...
  4. Timing cover rubber seals

    Jafromobile:Not sure how well it worked for him, but it's an option for you.
  5. ECUflash Not Lean In Closed Loop But Fuel Trims Always High

    Did you touch the deadtimes / latency's? I only see you mention adjusting the injector scaling.http://ceddy.us/tuning/injectors/I use the steps listed above for injector tuning.
  6. ECUflash Excessive knock and crazy backfire

    Do you have any means of posting the tune that is currently in the car for others to look at for you? Perhaps you can get your tuner to email it to you?If not, one thing that comes to mind is there are two separate timing maps in the ECU. A high octane timing map and a low octane timing map...
  7. 6bolt Engine Assembly - test springs/valve clearance/degree

    Great videos about this subject:
  8. 2G 99 GST Cylinder 3 Misfire

    What ECU and CAS are you running?
  9. ECUflash Turn off cel in ECUFLASH w/touching peripheral bits

    Short answer, yes.What code are you getting?
  10. 2G Ceddy mods and P0446

    Sorry to hear. More than likely its bricked. I believe its from the connector and voltage.Years ago when I first started messing with ecuflash, my laptop locked up and got blue screen of death in the middle of a flash. I shit a brick cause my car wouldn't run at all. I was able to reflash it...
  11. 2G Ceddy mods and P0446

    Its been a long time since I did this, but I believe I replaced the ceddy mod hex and xml files with the ones in the zip file that included the emissions tables. You should compare them, just to make sure. They should be the same until the end, then there is code written that creates the...
  12. 2G Ceddy mods and P0446

    http://www.dsmtuners.com/threads/force-obd-inspection-pass-2g.394945/page-3Post #57orPost #62
  13. Resolved injector misfire

    I tried to move my wiring harness as little as possible when I switched injector #4 with #3. When I made this switch, I started the car and held the RPM's above 3,500 until it misfired. When I checked the injectors, #2 (which wasn't touched) wasn't clicking, hence my confusion.This I am not...
  14. 1G HY35 O2 Housing

    http://www.mandrel-bends.com/catalog/holset-hx35-turbo-outlet-flange-wg-blocked-1-2-mild-steel-2298.htmlI just bought everything from this company to make my hy35 O2 housing. Turbo flange, downpipe flange, and 2.5" pipe.
Support Vendors who Support the DSM Community
Boosted Fabrication ECM Tuning ExtremePSI Fuel Injector Clinic Innovation Products Jacks Transmissions JNZ Tuning Kiggly Racing Morrison Fabrications MyMitsubishiStore.com RixRacing RockAuto RTM Racing STM Tuned
Back
Top